Outdoor Chair Feet on Deck and Stone Terraces
Most terrace complaints about outdoor chairs are not about the frame but about what the foot does to the floor underneath it: dents in softwood decking, brown rings on limestone, black prints on porcelain tile. All three are contact problems, and all three are decided at the foot, not the frame.
Published by JPChairs · Chair manufacturer in Foshan, China · 2026-11-12
What the foot actually presses into
The seated guest plus a 6 to 9 kg aluminium or rattan frame puts 110 to 140 kg through four feet, 27 to 35 kg each. On stone that is nothing: sandstone and granite carry compressive strengths above 100 MPa. On timber decking it is everything, because a deck board is a 25 or 28 mm softwood panel spanning joists at 400 mm, and its weak direction is a point load at mid-span.
- The bare 20 mm nylon glide under 30 kg reaches about 950 kPa on its 4 square centimetres of face, enough to crush softwood fibres.
- The same load on a 40 mm polymer pad spreads to about 240 kPa, and on a 60 mm rubber-cored pad to about 105 kPa, below the level that prints on kiln-dried pine.
- Sustained load matters as much as peak load: furniture left all season on thermally modified timber dents at contact pressures that a daily reset would never cause.
Why the mark on stone is staining, not damage
The black or brown ring on stone or porcelain is usually chemical transfer, not pressure. Three culprits cover most cases.
- Plated steel feet rust from the inside once water sits in the cup of the glide, and iron oxide migrates into limestone and concrete permanently. Stainless feet or fully enclosed polymer pads are the fix.
- Cheap PVC glides soften above roughly 40 C of deck surface temperature and their plasticisers migrate into the coating, leaving a dark print. We stopped fitting bare PVC after seeing prints on porcelain after one summer.
- Filler-heavy rubber does the same once the surface UV-ages. Mark-free certified EPDM and polypropylene are the two materials we trust on stone.
Water trapping and deck rot under flat pads
On a deck the danger is not weight but water held against the board. A flat pad seals a disc of the surface, and after rain that disc keeps the board wet for hours in shade. Repeated wetting cycles are how surface rot and black mould rings start.
- Pads with 2 to 3 mm drainage ribs on the face cut wet contact area by about 70 percent and let the board dry out between services.
- Raised ring feet that touch down on an 8 to 10 mm rib instead of a full face work even better, at about 0.15 to 0.25 USD per foot more.
- Feet must not span the 5 to 6 mm gap between deck boards: a pad wider than the board rocks on the gap and cracks board edges, so we keep outdoor foot diameters at 40 mm or less on standard decking.
Pad materials compared for outdoor use
- Nylon: hardest and most dent-prone on timber, fine on stone and tile, 0.10 to 0.18 USD per foot.
- Ribbed polypropylene: the default we fit, UV-stabilised, no staining, 0.15 to 0.30 USD.
- EPDM rubber: best grip on slippery stone and the quietest, but only from a maker who certifies mark-free testing, 0.25 to 0.45 USD.
- Felt: indoor restaurant use only; outdoors it holds water, grit cuts it within a season and it delaminates from the metal cup.
- Stainless caps with EPDM inserts: the premium choice for coastal stone terraces, 0.80 to 1.20 USD and effectively permanent.
Hybrids are common and sensible: a nylon shell with an EPDM contact face gives the wear life of the shell and the floor behaviour of the rubber at about 0.35 USD per foot.
How we choose and fit feet before packing
Foot choice is an order-sheet field, not an afterthought. For every outdoor order we record the destination surface where the buyer tells us, and the default matrix is simple: decking gets ribbed PP at 40 mm, natural stone gets EPDM-faced feet, porcelain and tile get nylon with EPDM inserts. Every foot is pressed on with a rated adhesive or screwed onto a threaded insert, because push-on feet fall off in transit and a bare tube end does exactly the damage the pad was meant to prevent.
Fit check is a 30 kg push at 45 degrees on a sample board: no slide, no spin, and no mark after 24 hours. Buyers can see how these feet are fitted across our outdoor chairs for timber decking and stone, and if a project sits on an unusual surface such as recycled composite boards, we confirm the pad choice against the deck protection FAQ before the order is locked.
The three specs to write into a terrace order
- Foot diameter and material per surface: 40 mm ribbed PP for decking, EPDM-faced for natural stone, nylon plus EPDM insert for porcelain and tile.
- Fixing method: screwed or threaded insert for anything above 25 kg of seated load, with four spare feet per chair packed in the carton.
- The no-mark clause: 30 days of contact at 60 C on light porcelain with no print, which is the test that separates filled rubber from real EPDM.
Those three lines cost between 0.60 and 1.80 USD per chair and prevent the two claims that actually arrive from terrace projects: dented decking and stained stone. Both are cheaper to prevent at the glide than to argue about after handover.


