Bar Stool Seat Pads: Attachment & Re-covering
The bar stool seat pad is the first thing a guest touches and the first thing a service team replaces. On our floor the attachment method is chosen before the foam is cut, because a pad that is glued down cannot be recovered without scrapping the foam underneath, and that single decision moves a venue's five-year cost more than the price of the stool itself.
Published by JPChairs · Chair manufacturer in Foshan, China · 2026-11-12
Four ways a pad attaches to a bar stool frame
We build bar stool pads four ways, and the differences show up years later, not on delivery day.
- Glued: 12 mm birch ply pan, foam bonded with contact adhesive sprayed at 80 to 100 g per square metre, fabric pulled and glued to the pan underside. Cheapest at about 0.35 USD of consumables per pad, but the first re-cover destroys the foam.
- Stapled: fabric folded under the ply and fixed with No.71 staples, 10 mm leg, 24 to 30 staples per pad. Recoverable three or four times before the ply edge frays.
- Screwed into weld nuts: four M5 by 16 pan-head screws into weld nuts fused to the frame, torqued to 3.5 to 4.5 Nm. The whole pad lifts off in two minutes with a T20 bit.
- Bolted through: M6 bolts pass through the pan into a seat plate on the frame, with nylon-patch thread locking. The slowest to build and the most recoverable.
Bars that re-theme every two or three years should never order glued pads: the fabric change becomes a foam change, and the foam change doubles the kit cost.
Why weld nuts beat self-tapping screws
The cheap way to make a pad removable is to drive four self-tapping screws straight into the tube wall. It works on the sample and fails on site. A 1.2 mm tube wall gives a thread about four pitches deep, and a bar pad is leaned on, rocked and lifted hundreds of times a day. We measure pull-out at 900 N on a fresh weld nut against 380 to 450 N on a self-tapper after 500 insertions.
The weld nut is fused to the tube before powder coating, so the hole is masked during coating and the thread arrives clean. The nut costs about 0.08 to 0.12 USD each, four per stool, and insertion torque stays inside a 1 Nm band across thousands of removal cycles. For all-day venues we do not quote self-tapping pads at all.
Foam and ply spec under a bar pad
Bar service is heavier than dining service because guests perch rather than sit, and the pad takes point loads at the front edge.
- Ply pan: 12 mm birch for pads up to 400 mm, 15 mm above that, so a 110 kg guest on the front edge keeps pan deflection under 2 mm.
- Foam: 35 to 40 kg per cubic metre at 40 mm, with 25 percent IFD between 110 and 140 N per ISO 2439.
- Compression set: ASTM D3574 method D after 22 hours at 70 C, held at 5 percent or better, which is what stops the pad going flat by month 18.
- The 3 mm dacron interliner over the foam softens the front roll and adds about 0.25 USD per pad.
Fabric and leather quantities per pad
The 420 by 420 mm pad with a 60 mm wrap needs about 0.48 square metres of fabric including the fold under the ply. We quote 0.55 to cover pattern matching on stripes, so 100 pads take a 55 metre roll. Leather runs on hide yield instead: only 60 to 70 percent of a hide is usable after scars and shape are cut around, so 100 pads need about 8 square metres of hide, not 5.5.
Per-pad material lands around 0.90 to 1.30 USD for contract vinyl, 1.60 to 2.40 USD for woven contract fabric and 3.50 to 6.00 USD for corrected-grain leather. What moves the number most is not the material but the yield assumption, and that is where a quote without a cutting plan goes wrong.
The re-cover cycle in real numbers
In a full-service bar we see pads re-covered every 18 to 30 months; in cafes where pads are wiped rather than scrubbed, 36 to 48 months is common. The fixing method decides what that visit costs.
- Screwed or bolted pad: unscrew four fixings, strip the old cover, fit the new one, refasten. Our workshop does it in 14 to 18 minutes per pad, about 3.20 USD of labour.
- Stapled pad: add staple removal and ply dressing, 20 to 26 minutes, and after the third cycle the pan is replaced along with the cover.
- Glued pad: stripping destroys the foam, so the kit is new ply, new foam and new cover at 4.80 to 6.50 USD per pad plus 35 to 45 minutes of shop time.
Across a 120-stool bar and two re-cover cycles, choosing weld nut fixings over glue saves roughly 1,100 USD in kits and labour.
What goes into the order and the carton
When a pad is designed to be removed, the hardware has to ship with the stools rather than be sourced later. Every stool with screwed pads leaves with four spare M5 screws bagged inside the carton, and every 100 stools carry two complete spare pads, enough to cover transit damage and the first month of abuse. Pads pack in a separate carton layer with 5 mm foam interleaves so the front roll does not print into the cover below.
The spec sheet states pan size, foam IFD band, fixing type and torque in writing, and the same numbers run through our commercial bar stools with replaceable seat pads. For a custom pad shape or a venue re-cover programme, the OEM seat pad fixing drawings are issued before tooling so the weld nut positions stay locked for every future order.


